ASTM C – 03 Estimate of the Heat Gain or Loss and the Surface Temperatures of This standard is issued under the fixed designation C ; the number. This standard is issued under the fixed designation C ; the number 1 This practice is under the jurisdiction of ASTM Committee C on Thermal. Insulation . 23 Feb Already shared in my big collection, check there for more. C Standard Practice for Estimate of the Heat Gain or Loss and the Surface.

Author: Kazirg Felkis
Country: Grenada
Language: English (Spanish)
Genre: Literature
Published (Last): 14 June 2018
Pages: 483
PDF File Size: 8.53 Mb
ePub File Size: 10.11 Mb
ISBN: 333-2-31499-113-5
Downloads: 52439
Price: Free* [*Free Regsitration Required]
Uploader: Yozshuhn

It is the responsibility satm the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This facilitates problem solution and increases the probability of successful computer runs. Need more than one copy? In it is stated that the standard has for convective coefficient the following for pipes: However, additional information on effects of wind velocity, jacket emittance, ambient conditions and other influential parameters may also be required to properly select an insulation system. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Also, phase change of a gas, liquid, or solid within a solid matrix or phase change by other mechanisms will provide abrupt changes in the temperature dependence of thermal conductivity.

ASTM C – Heat Transfer & Thermodynamics engineering – Eng-Tips

Due to the large number of combinations of size, temperature, humidity, thickness, jacket properties, surface emittance, orientation, and ambient conditions, it is not practical to publish data for each possible case, Refs 78. Join your peers on the Internet’s largest technical engineering professional community. The use of this practice by both manufacturers and users of thermal insulation will provide standardized engineering data of sufficient accuracy astmm predicting thermal insulation system performance.


The Architecture, Engineering and Construction AEC industry is constantly looking for process improvements to better manage potential project delays and costs. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Computers are readily available to most producers and consumers of thermal insulation to permit the use of this practice. Click Here to join Eng-Tips f680 talk with other members! The exterior surface temperature of the insulation is often shown to provide information on personnel protection or surface condensation. Certain applications may need specific data to produce meaningful results.

With the existence of radiation and convection modes of heat transfer, the measured value should be called apparent thermal conductivity as described in Terminology C To date, there is no accepted system of metric dimensions for pipe and insulation systems for cylindrical shapes. It’s asym to join and it’s free. Under this system, intermediate output guides the user to make programming adjustments to the input parameters as necessary.

The equations used in Practice C analysis yield “averaged” results for the entire surface in question.

The Eng-Tips staff will check this out and take appropriate action. As the voice of the U. When an international standard for piping and insulation sizing occurs, this practice can be rewritten to meet c6880 needs.

This data is presented for typical insulation thicknesses, operating temperatures, surface orientations facing up, down, horizontal, verticaland in the case of pipes, different pipe sizes. For each test case, the results for heat flow and surface temperature must be ashm within resolution of the method to those obtained using the practice described herein.

In addition, it has been demonstrated that astk practice can be used to calculate heat transfer for circumstances other than insulated systems; however, these calculations are beyond the scope of this practice. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.


You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. In the cylindrical coordinate ashm, Practice C can be applied to radial heat flows for all types of piping circuits.

No conflict exists with such modifications as long as the user verifies the modifications using a series of test cases that satm the range for which the new method is to be used. Link to Active This link will always route to the current Active version of the standard. The computer program is intended for flat slab, pipe and hollow sphere insulation asmt. In the spherical coordinate system, Practice C can be applied to radial heat flows to or from stored fluids such as liquefied natural gas LNG.

Register now while it’s still free! The change in thermal conductivity with temperature is different for different materials, and for operation at a relatively small temperature difference, an average thermal conductivity may suffice.

Air blowing across real objects often follows flow directions and velocities much different from the direction and velocity of the main free stream.

For this reason, the convective surface coefficient calculation cannot be expected to be accurate at each location on the surface unless the wind velocity measurements are made close to the surface and a separate set of equations are applied that calculate the local surface coefficients. This cost can be substantially reduced by the use of accurate engineering data tables, or available computer analysis tools, or both.