Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual (basic) is intended for users who “just want to run the inverter”. If you are going to utilize.

Author: JoJozilkree Gokree
Country: Suriname
Language: English (Spanish)
Genre: Business
Published (Last): 18 July 2015
Pages: 324
PDF File Size: 4.41 Mb
ePub File Size: 11.38 Mb
ISBN: 505-8-52094-282-3
Downloads: 64475
Price: Free* [*Free Regsitration Required]
Uploader: Yozshugis

NOTE Depending on the machine, vibration may not be reduced enough or an effect may not be produced.

Afterwards you can then reset Pr. Page all clear is executed from RS communication. The motor speed fluctuation at load fluctuation can be adjusted using Pr. When data receive errors occur consecutively and exceed the mitsubishi e700 inverter manual number of retries set, an inverter trips E.

OFF position changes the terminal 4 to the voltage input specification. Page 62 Connection of stand-alone option units Wiring 3.

Page – User groups Pr. If operation is performed in a high frequency range, the current at motor lockup becomes smaller than the rated output current of the inverter, and the protective function OL is not executed if the motor is at a stop.


Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller

It is not suitable for machines such as mitsubishi e700 inverter manual machine and wrapping machine which requires less uneven rotation at low speed. When the magnetic contactor is turned on while the inverter is operating, overcurrent protection of inverteer inverter and such will activate.

When multiple motors are operated by a single inverter, protection cannot be provided by the electronic thermal relay function. Enter text from picture: Page Page Page – Selection of operation mode and operatio Independently of whether the inverter is running or at a stop, the frequency can be set by merely turning the digital dial.

Misoperation prevention and parameter setting restriction Parameter Reset selection You can select the enable condition of reset function RES signal, reset mitsubishi e700 inverter manual through com- munication input. Mitsubjshi not mount it horizontally or any other way. A special motor cannot be protected by the electronic thermal relay function. Page 70 – Connection of the manhal regeneration com Connection of stand-alone option units Wiring 3.

This function prevents the inverter from being inoperative by the external command if the mode is accidentally left unswitched from the PU operation mode. After the inverter has started up in the network operation mode, parameter write and operation can mitsubishi e700 inverter manual performed from a program.

To reinstall, mitsubishi e700 inverter manual the cover to the inverter along the guides.



Special operation Parameter 6. When any value other than “” is set to Pr.

Page Page – When the rated motor frequency is 60Hz Make mitsuboshi that the running speed setting is correct. To print the manual completely, please, download it. The data check time changes depending mitsubishi e700 inverter manual the instruction code. SU up to frequency Inverter b4: Inverter status monitor Read Refer to page for details. Connection of stand-alone option units Wiring It is recommended to configure a sequence, which shuts off power in the input side of the in- verter by the external thermal relay as shown mitsubishi e700 inverter manual, to prevent overheat and burnout of the high duty brake resistor FR-ABR in case the regenerative brake transistor is damaged.

Page OFF position changes mitsubishi e700 inverter manual terminal 4 to the voltage input specification. Simple mode parameter list Basic settings Selection method of general-purpose magnetic flux vector control Perform secure wiring.

When output torque torque current exceeds the stall prevention operation level, the output fre- quency is controlled to limit the output torque.