View and Download Honeywell VOYAGER G user manual online. Single- Line Laser Scanner. VOYAGER G Scanner pdf manual download. View and Download Honeywell Voyager g user manual online. Voyager g Barcode Reader pdf manual download. Also for: Voyager g. Voyager™ g, User’s guide • Read online or download PDF • Honeywell VOYAGER G User Manual.
|Published (Last):||18 July 2014|
|PDF File Size:||15.16 Mb|
|ePub File Size:||9.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
Honeywell VOYAGER 1200G User Manual
Page Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Page 85 To rename scanners with sequential, numeric names, scan the following bar codes. Scan the Reset code voyagwr each name change and wait for the scanner to relink to voyager 1200g manual base.
Symbologies This programming section contains the following menu selections. Straight 1200h Of 5 Voyager 1200g manual Message Length scan a redundancy count between 0 and 10 on the Programming Chart voyager 1200g manual the back cover of this manual. Isbt Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual.
Move Commands A-4 for decimal, hex and character codes.
Honeywell Voyager 1200g User Manual
When Check Digit is set to Validate and Transmit, the scanner only reads NEC voyager 1200g manual of 5 bar codes printed voyaber a check digit, and will transmit this digit at the end of the scanned data. After scanning one of these codes, you must power cycle the cash register. Page Programming Chart As a general rule, the following characters are sup- voyager 1200g manual, but need special care for countries other than the United States: Sends numeric characters as if entered from a numeric keypad.
Longer delays are effective in minimizing accidental rereads.
The user may find the fol- lowing booklet helpful: Scan the bar code below, then set the timeout from milliseconds by scanning digits from the Programming Chart, then scanning Save. Don’t voyager 1200g manual me this message 1200f.
Serial Programming Commands The serial programming commands can voyager 1200g manual used in place of the programming bar codes.
By pressing ‘print’ button voyager 1200g manual will print only current page. Data transmission continues where it left off when XOFF was sent.
Codabar Message Length Scan the bar codes below to change the message length. This bar code sets the baud rate to bps and the data format to 8 data bits, no parity, 1 stop bit. Search Commands Move the cursor to the beginning F7 Move the cursor to the first character in the input message.
UPC-A Check Digit This selection allows you to specify whether the voyager 1200g manual digit should be transmitted at the end of the scanned data or not. The error beep sound is pro- page This table applies to U.
Cordless System Operation Note: If the scanner provides a single good read beep and the green LED lights, the scanner has successfully linked to the base. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. Responses Responses The device responds to serial commands with one of three responses: Page Programming Chart They reset the scanner voyager 1200g manual the custom default settings see Setting Custom Defaults page Scan three numeric bar codes on the Programming Chart to program the scanner for your terminal ID you must enter 3 digits.
Tighten the two screws to 1200 the connector to the port. Page UPC-A Check Voyager 1200g manual This selection allows you to specify whether the check digit should be transmitted at the end of voyager 1200g manual scanned data or not.
This voyageg but is not limited to: No data is output unless the sequence is read. Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. For complete descriptions and examples voyager 1200g manual each serial pro- gramming command, refer to the corresponding programming bar code in this manual.
HONEYWELL VOYAGER G USER MANUAL Pdf Download.
Don’t have an account? If you scan the Require User-Defined Sequence code, the data combina- tion specified in the User-Defined concatenation sequence is voygaer to transmit the data. When an odd number of characters is present, it is due to NULL characters embedded in the bar code. Technical Assistance For our latest contact information, please check our website at the link above.
Plessey Message Length When Check Character is set to Validate and Transmit, the scanner only reads Plessey bar voyager 1200g manual printed with a check character, and will transmit this character at the end of the scanned data. Once the scanner voyager 1200g manual base has been fully connected, power up the computer.
Scan the bar code below, then set the timeout from milliseconds by scanning digits from the Programming Chart, then voyager 1200g manual Save. Page 3 The user may find the fol- lowing booklet helpful: Turn the base upside down. End Object Detection After Voyager 1200g manual Read After a manua code is successfully detected and read from the scanner, the laser can be programmed either to remain on and scanning, or to turn off.